We are open Monday to Friday from 1 PM to 6 PM and Saturday from 10 AM to 2 PM

Electric Kettles

Electric Kettles
This Electric Kettle is designed to rapidly heat up beer in a few minutes, allowing you to enjoy a freshly brewed brew faster. This Electric Kettle is a great addition to any beer enthusiast's kitchen.

17 productos

  • Distillation Lid for 35L BrewZilla / DigiBoil

    Distillation Lid for 35L BrewZilla / DigiBoil

    No disponible en stock

    Used to adapt your 35L BrewZilla or DigiBoil into a still. Allows for a copper still top to fit on the lid. This lid has a 1.85 in. (47 mm) hole for the still top. Lid gasket included. Made from 304 stainless steel. Measures 12.25" in diameter.

    No disponible en stock

    $35.99

  • DigiMash Upgrade Kit for 35L DigiBoil | Gen 1

    DigiMash Upgrade Kit for 35L DigiBoil | Gen 1

    No disponible en stock

    Please note: This kit is intended for use with Gen 1 35L DigiBoils. It has a slightly larger wire support ring that may not fit Gen 2 DigiBoils. If you're unsure which generation your unit is, check the base. Gen 1 units have rubber feet and Gen 2 units have a molded plastic base. DigiMash Upgrade Kit for 35L DigiBoil. Includes everything you need to use the DigiBoil as an electric, digitally controlled mash tun. Includes: False bottom Malt pipe Wire support  Malt pipe handle Malt pipe bottom screen

    No disponible en stock

    $99.99

  • DigiBoil Electric Kettle - 35L/9.25G 220v

    DigiBoil Electric Kettle - 35L/9.25G (220v)

    No disponible en stock

    The DigiBoil electric kettle can serve a surprisingly wide range of functions. It's perfect for 5-gallon extract batches, preheating strike or sparge water, and with the addition of a still top lid and condenser, it can be used for home distilling. With the Mash Upgrade Kit, you can easily use the DigiBoil as an electric mash tun. This model runs off 220V power and has dual heating elements (1900w and 500w) that can be controlled independently. Includes 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2"). Features: 304 stainless steel construction 9 gallon total capacity Digital temperature control 220V / 15A power NEMA 6-30R plug (5 ft. cord) Stamped-in volume markers (gallons & liters) Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C Compatible with reflux and pot still (DS130 & DS120)* External Dimensions: 29" H x 15" W (including handles) Internal Dimensions: 19.5" H x 11.75" W ETL Listed *Distilling: using the DigiBoil with a distilling condenser requires the still top lid and gasket Warning: Distilling alcohol without permits or licensing is illegal in many countries, including the United States.  It is the customer's responsibility to research their local, state, and federal laws and abide by those laws. Brewmaster is not responsible for any damage or injury caused by either misuse or unlawful use. Stills can also be used to produce essential oils, vinegar, purified water and engine fuel (requires permit in USA). 

    No disponible en stock

    $199.99

  • Anvil Foundry™ - 10.5 Gallon with Recirculation Kit

    Anvil Foundry™ - 10.5 Gallon with Recirculation Kit

    No disponible en stock

    Key Features: Patented Dual Voltage Switchable Between 120V 1600W, 13A and 240V 2800W, 12A for Faster Heating & Better Boils. (240V Standard) Large Capacity Increases Efficiency and Grain Capacity. Double Wall Insulation Maintains Mash Temps and Increases Heating Speeds. Ultra Low Watt Density, Triple Element Heaters - Won't Scorch. Linear Digital Power Control and Solid-State Switching for Fine Tuning your Boil. Turbo 500 Distillation Ready. Includes High Capacity Stainless Immersion Chiller with Hoses & Fittings. External Pump Won't Plug and is Easy to Clean. No Need to Disassemble Entire Unit! Use for Other Pumping Needs too. Optional Recirculation Pump Kit - $99.99. Optional Swirly™ Whirlpool Optional Steam Condenser Max Grain Capacity - 16 lbs 10.5 DimensionsTank Diameter = 12.5 inchesDistance Across the Handles = 17 inchesHeight of Base Unit = 29.75 inchesLid = 3.25 inchesTotal Height = 33 inchesSpigot Height from Base = 7 inchesShipping Weight = 38 lbs Wattage120V = 1600 watts240V = 2800 watts

    No disponible en stock

    $524.00

  • DigiMash Electric Brewing System | Gen 2 DigiBoil | 35L | 9.25G | 110V

    DigiMash Electric Brewing System | Gen 2 DigiBoil | 35L | 9.25G | 110V

    No disponible en stock

    The DigiMash is one of the most affordable options in all-grain electric brewing. Includes 35L DigiBoil, false bottom, malt pipe with bottom screen, wire support, and malt pipe handle. This model runs off 110V power and has dual heating elements (1000w and 500w) that can be controlled independently. Includes 304 stainless steel 1/2" ball valve with 13mm barb (approx. 1/2"). DigiBoil Features: 304 stainless steel construction 9 gallon total capacity Digital temperature control 110V / 15A power and plug (5 ft. cord) Stamped-in volume markers (gallons & liters) Temperature reads in °F or °C With elements turned off, hold both +/- buttons to switch between °F or °C Recommended max. grain bill - 18 lbs Recommended min. grain bill - 8 lbs External Dimensions: 29" H x 15" W (including handles) Internal Dimensions: 19.5" H x 11.75" W Mash Upgrade Includes: False bottom Malt pipe Wire support  Malt pipe handle Malt pipe bottom screen Installation & Use: Place the false bottom inside the kettle Install the wire support in the channel located at the top of the kettle Place the mesh screen inside the malt pipe and attach the handle Lower the malt pipe into the kettle so it rests on the wire support Fill with strike water and heat to desired strike temperature When desired temperature is reached, add grain and stir until well mixed When your mash is complete, use the handle to lift out malt pipe and rotate 90° so the malt pipe feet sit on the wire support Allow the wort to drain into the kettle and sparge the grain with warm water (165-175°F) When you're done collecting your wort, remove the malt pipe and proceed to boil

    No disponible en stock

    $299.99

  • 1600 Watt Stainless Steel Heating Element

    1600 Watt Stainless Steel Heating Element

    No disponible en stock

    A powerful, 304 stainless steel heating element well suited for most kettles. With its weldless design and a diameter of 1 1/4" it's easy to install. Install by simply drilling a 1.25" hole in your kettle and tightening the nut from the outside. The heating element requires a power cord which can be purchased separately (Electrical connection requires a computer power connection IEC320 C13 to your 110 v plug). 11.5" Long Features: 1600 watt 110 v element Food grade, high temperature silicone seal The element itself is 11.5" long, 0.75" diameter Designed for use with 5 gallon batches Please Note - Having electrical devices around liquid can be hazardous, and should not be left unattended. Please use caution while using this device, and read the instruction manual prior to use. Use the 1.25" Hole Saw to drill a hole for this product.

    No disponible en stock

    $65.99

  • Anvil Foundry™ - 6.5 Gallon

    Anvil Foundry™ - 6.5 Gallon

    No disponible en stock

    The ANVIL Foundry™ is the most versatile all-in-one brewing system available. From the triple element low watt density PATENTED dual voltage heaters for blazing fast heating speeds, to the unique high flow grain basket, you won’t find a more powerful feature-rich product. Key Features: Patented Dual Voltage Switchable Between 120V 1600W, 13A and 240V 2800W, 12A for Faster Heating & Better Boils. Large Capacity Increases Efficiency and Grain Capacity. Double Wall Insulation Maintains Mash Temps and Increases Heating Speeds. Ultra Low Watt Density, Triple Element Heaters - Won't Scorch. Linear Digital Power Control and Solid-State Switching for Fine Tuning your Boil. Turbo 500 Distillation Ready. Includes High Capacity Stainless Immersion Chiller with Hoses & Fittings. External Pump Won't Plug and is Easy to Clean. No Need to Disassemble Entire Unit! Use for Other Pumping Needs too. Optional Recirculation Pump Kit - $99.99. Optional Swirly™ Whirlpool Optional Steam Condenser 6.5 DimensionsTank Diameter = 12.5 inchesDistance Across the Handles = 17 inchesHeight of Base Unit = 21.25 inchesLid = 3.25 inchesTotal Height = 24.5 inchesSpigot Height from Base = 7 inchesShipping Weight = 23 lbs Wattage120V = 1600 watts240V = 2800 watts

    No disponible en stock

    $349.00

  • Anvil Foundry™ - 6.5 Gallon with Recirculation Kit

    Anvil Foundry™ - 6.5 Gallon with Recirculation Kit

    No disponible en stock

    The ANVIL Foundry™ is the most versatile all-in-one brewing system available. From the triple element low watt density PATENTED dual voltage heaters for blazing fast heating speeds, to the unique high flow grain basket, you won’t find a more powerful feature-rich product. Key Features: Patented Dual Voltage Switchable Between 120V 1600W, 13A and 240V 2800W, 12A for Faster Heating & Better Boils. Large Capacity Increases Efficiency and Grain Capacity. Double Wall Insulation Maintains Mash Temps and Increases Heating Speeds. Ultra Low Watt Density, Triple Element Heaters - Won't Scorch. Linear Digital Power Control and Solid-State Switching for Fine Tuning your Boil. Turbo 500 Distillation Ready. Includes High Capacity Stainless Immersion Chiller with Hoses & Fittings. External Pump Won't Plug and is Easy to Clean. No Need to Disassemble Entire Unit! Use for Other Pumping Needs too. Optional Recirculation Pump Kit - $99.99. Optional Swirly™ Whirlpool Optional Steam Condenser 6.5 DimensionsTank Diameter = 12.5 inchesDistance Across the Handles = 17 inchesHeight of Base Unit = 21.25 inchesLid = 3.25 inchesTotal Height = 24.5 inchesSpigot Height from Base = 7 inchesShipping Weight = 23 lbs Wattage120V = 1600 watts240V = 2800 watts

    No disponible en stock

    $448.00

  • DigiMash Upgrade Kit for 65L DigiBoil

    DigiMash Upgrade Kit for 65L DigiBoil

    No disponible en stock

    DigiMash Upgrade Kit for 65L DigiBoil. Includes everything you need to use the DigiBoil as an electric, digitally controlled mash tun. Includes: False bottom Malt pipe Wire support  Malt pipe handle Malt pipe bottom screen

    No disponible en stock

    $179.99

  • Grainfather G30 Control Box – US/CAD 120V

    Grainfather G30 Control Box – US/CAD (120V)

    No disponible en stock

    Control Box Features: Bluetooth connection to your mobile device so it can be controlled remotely  PID algorithm works in conjunction with a triac for more stable heating and so you can control power output Programmable step mashing Delayed heating - fill your Grainfather with water the night before and wake up to your water at strike temperature ready for brewing straight away Change between celsius and fahrenheit easily Waterproof graphic display Lugs at rear which can be changed to suit any Grainfather currently on the market Use in manual mode or with app App Features: Grainfather Grain Kit recipes provided in app Import Beer XML files  Set your own boil temperature (for different altitudes) Change between celsius and fahrenheit easily Grainfather calculators provided in app Online recipe creator - create, share, rate and review brews through this central hub. Then when ready, sync with your app.

    No disponible en stock

    $149.99

  • BrewZilla All Grain Brewing System | Gen 3.1.1 | 35L/9.25G | Built-in pump | Wort chiller included | 220V

    BrewZilla All Grain Brewing System | Gen 3.1.1 | 35L/9.25G | Built-in pump | Wort chiller included | 220V

    No disponible en stock

    The Robobrew is an all-in-one electric brewing system that has built-in elements for heating and boiling, programmable mash schedule and delayed start, a built-in pump for recirculation, an onboard water resistant control panel for setting and monitoring temperatures, a removable grain basket, and a built-in spigot for transferring. This more powerful version of the Robobrew requires 220V power. The V3.1.1 unit features an upgraded main circuit board that changes how the automatic step mashing functions. Now when moving from step to step, the timer for each step will not begin counting down until the programmed temperature is reached. This means more accurate mash schedules than ever before! The new board also introduces boil addition timers so you'll never miss the mark for hop additions. Automatic Step Mashing! One of the coolest features of the Robobrew is the ability to program the unit with up to 6 individual temperatures and durations so you can step mash precisely how you desire. Simply press the "S1-S6" button to select the stage you want to adjust, and use the temp, time and +/- buttons to program the stage. If you have less than 6 stages in your mash schedule, program the stages you want to skip with 00:00 as the time and the controller will automatically move on to the next step. When all the stages are complete, the Robobrew will sound an alarm and hold the last set temperature. The programmable stages can also be used to set a delayed start of up to 23 hours in advance so that you can have your water hot and ready to go when you get home from work or wake up in the morning. In order to do this, fill the unit with strike water and program the controller with two steps. Step 1 should be programmed at a temperature lower than the unheated strike water (so the elements will remain off), and the duration should be programmed for however long you want the delay. Then program Step 2 with your desired strike water temperature and a duration of 1-2 hours, giving the Robobrew ample time to heat up and giving you a margin of error in case you hit the snooze button the morning of brew day. Built-in magnetic drive pump to easily recirculate the wort during the mash. We recommend getting some silicone tubing to go with the recirculation arm. This allows you more control over the recirculation and you can then use the pump to transfer your wort to your fermenter. As with any mash, be sure to stir your grain very thoroughly after mashing-in so you start out with an even temperature throughout the grain bed. Dual heating elements run off of a single 220 volt plug and have individual switches allowing for more control over the heating process. One element is 1900 watts and the other is 500 for a combined 2400 watts! Use both when you need to ramp up the temperature quickly either at the start to get to your mash temp or to go from your mash temp to boiling. Use only one of the elements when you want to hold a temperature. The digital control panel makes it easy to see the current temperature and set the temperature you want. The digital controller is also water resistant so don't worry about spills or some water dripping down the side. This controller is built for brewing! The brewery also includes a stainless steel malt pipe with false bottom allowing you to easily shift from mash tun to boil kettle during your brew day. The malt pipe includes a handle to lift it from the RoboBrew and tabs at the base so you can set the malt pipe over the RoboBrew to let the wort drain out. It also has feet at its base to raise the malt pipe slightly off the base and help prevent clogging. The included stainless wort chillers is shipped with bare ends so you can set it up for your situation. We list below the most common tubing and fittings sold to help connect to a hose, hose bib, or faucet.   If you have access to 220V power, this is definitely the unit we recommend. Although 110v power is enough to get up to boil, 220V will get you there faster and provide a much more vigorous boil.  Features: Gen 3.1.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons Digital temperature controller Automatic step mashing with 6 programmable stages 220V power NEMA 6-30R plug Dual heating elements for total control (1900 watts and 500 watts) Stainless steel 1/2 in ball valve for draining (don't have to use the pump) Immersion wort chiller included Stainless steel malt pipe/basket Stamped volume markers Glass lid Magnetic drive pump for recirculation Recirculation arm Temperature reads in °F or °C (press and hold temp button for several seconds to adjust) 32.75 in H (with recirculation arm) x 12.5 in D Recommended max. grain bill - 18 lbs Recommended min. grain bill - 8 lbsYou might also want: 2' of 1/2" ID Silicone tubing for sparging and draining. To connect included chiller: 20' of 1/2" ID tubing, 3 small hose clamps and 1 brass Garden Hose Thread by 1/2" barb adaptor. 

    No disponible en stock

    $599.99

  • ¡Últimas existencias! BrewZilla All Grain Brewing System With Pump | Gen 3.1.1 | 35L/9.25G 110V

    BrewZilla All Grain Brewing System With Pump | Gen 3.1.1 | 35L/9.25G (110V)

    1 en stock

    The BrewZilla is an all-in-one electric brewing system that has built-in elements for heating and boiling, programmable mash schedule and delayed startt, a built-in pump for recirculation, an onboard water resistant control panel for setting and monitoring temperatures, a removable grain basket, and a built-in spigot for transferring. It is extremely portable and uses 110V power so it can be used nearly anywhere.  The V3.1.1 unit features an upgraded main circuit board that changes how the automatic step mashing functions. Now when moving from step to step, the timer for each step will not begin counting down until the programmed temperature is reached. This means more accurate mash schedules than ever before! The new board also introduces boil addition timers so you'll never miss the mark for hop additions. New accessory! Check out the BrewZilla Whirlpool Arm, which uses the unit's internal pump to recirculate and spin the wort, improving hop extraction and chill times. No more stirring! Automatic Step Mashing!One of the coolest features of the BrewZilla is the ability to program the unit with up to 6 individual temperatures and durations so you can step mash precisely how you desire. Simply press the "S1-S6" button to select the stage you want to adjust, and use the temp, time and +/- buttons to program the stage. If you have less than 6 stages in your mash schedule, program the stages you want to skip with 00:00 as the time and the controller will automatically move on to the next step. When all the stages are complete, the BrewZilla will sound an alarm and hold the last set temperature. The programmable stages can also be used to set a delayed start of up to 23 hours in advance so that you can have your water hot and ready to go when you get home from work or wake up in the morning. In order to do this, fill the unit with strike water and program the controller with two steps. Step 1 should be programmed at a temperature lower than the unheated strike water (so the elements will remain off), and the duration should be programmed for however long you want the delay. Then program Step 2 with your desired strike water temperature and a duration of 1-2 hours, giving the BrewZilla ample time to heat up and giving you a margin of error in case you hit the snooze button the morning of brew day. Built-in magnetic drive pump to easily recirculate the wort during the mash. We recommend getting some silicone tubing to go with the recirculation arm. This allows you more control over the recirculation and you can then use the pump to transfer your wort to your fermenter. As with any mash, be sure to stir your grain very thoroughly after mashing-in so you start out with an even temperature throughout the grain bed. Dual heating elements run off of a single 110 volt plug and have individual switches allowing for more control over the heating process. One element is 1000 watts and the other is 500 for a combined 1500 watts! Use both when you need to ramp up the temperature quickly either at the start to get to your mash temp or to go from your mash temp to boiling. Use only one of the elements when you want to hold a temperature. The digital control panel makes it easy to see the current temperature and set the temperature you want. The digital controller is also water resistant so don't worry about spills or some water dripping down the side. This controller is built for brewing! The brewery also includes a stainless steel malt pipe with false bottom allowing you to easily shift from mash tun to boil kettle during your brew day. The malt pipe includes a handle to lift it from the BrewZilla and tabs at the base so you can set the malt pipe over the BrewZilla to let the wort drain out. It also has feet at its base to raise the malt pipe slightly off the base and help prevent clogging. The included stainless wort chillers is shipped with bare ends so you can set it up for your situation. We list below the most common tubing and fittings sold to help connect to a hose, hose bib, or faucet.   Note: The manual references an element for a different market.  This unit comes with two heating elements for a total of 1,500 watts. Features: Gen 3.1.1 Stainless steel construction 9 gallon total capacity with a finished beer output of 5-6 gallons Digital temperature controller Automatic step mashing with 6 programmable stages 110V power and plug Dual heating elements for total control (1000 watts and 500 watts) Stainless steel 1/2 in ball valve for draining (don't have to use the pump) Immersion wort chiller included Stainless steel malt pipe/basket Stamped volume markers Glass lid Magnetic drive pump for recirculation Recirculation arm Temperature reads in °F or °C (press and hold temp button for several seconds to adjust) 32.75 in H (with recirculation arm) x 12.5 in D Recommended max. grain bill - 18 lbs Recommended min. grain bill - 8 lbs

    1 en stock

    $599.99

  • Grainfather G70 - 220V

    Grainfather G70 - 220V

    No disponible en stock

    Just like the Grainfather G30, the G70 is your true brewing companion when it comes to making beer from grain. Thanks to the 70L capacity, homebrewers can now produce more beer to share or commercial breweries now have a unit that's small enough for pilot testing. It also has a smart controller with built-in wireless connectivity and mobile app integration for step-by-step remote-controlled brewing. The G70 gives you everything you need in one compact package that can be used virtually anywhere.https://youtu.be/z9STbBlkdKQ

    No disponible en stock

    $2,270.00

  • Grainfather G30³ 110V

    Grainfather G30³ 110V

    No disponible en stock

    Compact and simple to use, with a small footprint for brewing indoors the Grainfather G30³ provides a home brewery system that with superior design, innovative features and the latest technology, allows you to brew professional quality craft beer at home. The Grainfather, is your all in one brewing system, to make beer from grain. The sleek look, user friendly, intuitive design, and innovative features, make this your perfect brewing companion for both experienced and beginner all grain brewers. It is made from high quality 304 grade stainless steel with a 8 US Gal capacity, designed to make up to 6 US Gal of beer from one brew. The Grainfather G30³ includes The Grainfather unit and Counter Flow Wort Chiller.

    No disponible en stock

    $998.98

  • DigiMash Upgrade Kit for 35L DigiBoil | Gen 2

    DigiMash Upgrade Kit for 35L DigiBoil | Gen 2

    3 en stock

    DigiMash Upgrade Kit for 35L DigiBoil. Includes everything you need to use the DigiBoil as an electric, digitally controlled mash tun. The Gen 2 DigiMash Upgrade Kit is backwards compatible with Gen 1 DigiBoils. Includes: False bottom Malt pipe Wire support  Malt pipe handle Malt pipe bottom screen

    3 en stock

    $99.99

  • ¡Últimas existencias! 6" Bazooka Screen

    6" Bazooka Screen

    2 en stock

    Take your brewing experience to the next level with this 6" Bazooka Screen. Made from stainless steel, this 1/2" MPT fitting allows you to easily install this item into any brew kettle and filter out hops for a clearer wort. Perfect for preventing trub and sediment from entering your fermenter, this screen also allows you to turn any kettle into a mash tun. Get better results with this essential brew kettle item. The best 304 stainless steel mashing/boiling bazooka kettle screen Excellent to use for straining hops in a boil or in mash tun instead of a false bottom 1/2″ MPT fitting on one end to fit in brew kettle or any line of weld less ball valves This screen is heavy duty, makes a perfect companion for your mash tun or boiling kettle Specifications Material Stainless Steel 304 Body Thread 1/2" MPT Length 6"

    2 en stock

    $7.99

  • Anvil Foundry™ - 10.5 Gallon

    Anvil Foundry™ - 10.5 Gallon

    No disponible en stock

    The ANVIL Foundry™ is the most versatile all-in-one brewing system available. From the triple element low watt density PATENTED dual voltage heaters for blazing fast heating speeds, to the unique high flow grain basket, you won’t find a more powerful feature-rich product. Key Features: Patented Dual Voltage Switchable Between 120V 1600W, 13A and 240V 2800W, 12A for Faster Heating & Better Boils. (240V Standard) Large Capacity Increases Efficiency and Grain Capacity. Double Wall Insulation Maintains Mash Temps and Increases Heating Speeds. Ultra Low Watt Density, Triple Element Heaters - Won't Scorch. Linear Digital Power Control and Solid-State Switching for Fine Tuning your Boil. Turbo 500 Distillation Ready. Includes High Capacity Stainless Immersion Chiller with Hoses & Fittings. External Pump Won't Plug and is Easy to Clean. No Need to Disassemble Entire Unit! Use for Other Pumping Needs too. Optional Recirculation Pump Kit - $99.99. Optional Swirly™ Whirlpool Optional Steam Condenser Max Grain Capacity - 16 lbs 10.5 DimensionsTank Diameter = 12.5 inchesDistance Across the Handles = 17 inchesHeight of Base Unit = 29.75 inchesLid = 3.25 inchesTotal Height = 33 inchesSpigot Height from Base = 7 inchesShipping Weight = 38 lbs Wattage120V = 1600 watts240V = 2800 watts

    No disponible en stock

    $425.00

Ingresa en

¿Ha olvidado su contraseña?

¿Aún no tienes una cuenta?
Crear una cuenta