White, gas in quick disconnect with barb for gas line.Barb is 1/4". 1/4" or 5/16" beverage tubing is recommended for gas line.Tip N' Trick: Sometimes ball lock fittings are a challenge to quick disconnect "on and off" a cornelius keg. We recommend spraying the body connect on the keg first with a sanitizer solution which acts as a lubricant. When applying the ball lock fitting to the body connect, give a twist and turn to make it easier to connect. We've coined this term "Lube and Turn".
Pressure Fermentation Pressure fermentation is becoming more and more popular at the homebrew level, but in order to do it safely and accurately, you need a way to release excess pressure. You'll pressurize your vessel to your desired psi, but once fermentation begins and those hungry, active yeast start creating CO2, the pressure inside the vessel will increase. Attach a spunding valve and set it to your desired pressure, and it will blow off when the pressure gets to high and close up again when it's back to your desired psi. Pressure Transfers Even if you don't have a pressurizable fermenter, you may have done pressure transfers from keg to keg during filtering or after fining. During pressure transfers, it's a good idea to have a bit of head pressure in the receiving keg, especially if you're transferring beer that is already carbonated. Having a spunding valve in place will allow you to consistently control the head pressure and give you more consistent results, without losing carbonation in the process. Diaphragm vs. Poppet With the poppet style spunding valve, a spring pushes against a poppet to keep the valve closed. When the poppet lifts up to open, the surface area the gas pushes against becomes larger, and the spring has to work harder to push the poppet down and reseal the valve. This can lead to more gas being released than intended, and the remaining pressure in your vessel may be at a lower psi than your spunding valve’s set psi. Instead of a poppet, the spring inside the BlowTie pushes against a diaphragm, which has an immensely larger surface area. This means the surface area that the gas pushes against while the diaphragm is closed is significantly closer to the surface area it pushes against when the diaphragm is open. This leads to higher accuracy, and the remaining pressure after excess gas is released will be much closer to your set blow off pressure.
With this complete kit you'll be ready to use the BlowTie Spunding Valve right out of the box.
Release excess pressure on a pressurized fermenter or from a receiving keg during pressure transfers
Much more accurate than the spring and poppet style, and works much better at lower pressures.
Kit Includes: BlowTie, Pressure Gauge, Ball Lock Disconnect, Duotight Tee & Flared Duotight Fitting, 2x Lengths of EVABarrier 8mm OD Tubing
This Duotight elbow fitting is compatible with EVABarrier 8 mm OD Tubing.
Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines!
Features:
Insert tubing and firmly push to connect
Easily release tubing by pushing in the collet
Suitable for both gas & beverage applications
Made from food-grade acetal plastic
Double O-rings made from highly chemical resistant EPDM
Locking teeth made from stainless steel
Pressure rated to 150 psi
Temperature rated to 212°F (100°C)
This Duotight to Female Beer Thread fitting can be used to connect beverage line to faucet shanks instead of a tailpiece, and it's also a convenient option for connecting gas and beverage line to the gas in and bev out on keg couplers. Compatible with EVABarrier 8 mm OD Tubing (D1717 & D1718).
Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines!
Features:
Insert tubing and firmly push to connect
Easily release tubing by pushing in the collet
Suitable for both gas & beverage applications
Made from food-grade acetal plastic
Double O-rings made from highly chemical resistant EPDM
Locking teeth made from stainless steel
Pressure rated to 150 psi
Temperature rated to 212°F (100°C)
Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals.
Faucet shank and keg coupler not included.
Industry standard faucet for draft beer that fits North American shanks and towers. Chrome plating looks sharp and will keep your bar or kegerator looking amazing. Brass body with quick action brass lever. A great choice for replacing a worn out faucet.
Specifications:
Body Thread: 1 1/8” – 18 Thread (North American Beer Industry Standard)
Lever Thread: 3/8” – 16 UNC (Unified Coarse Thread)
Chrome Plated Brass Body
Brass Lever
Brand new stainless connectors that fit perfectly on your d ring tap. These are stainless steel and a high quality. Caps are also marked to ensure the correct connector for gas or liquid is used.
This Stout Faucet is perfect for a modern, stylish bathroom. Made of durable chrome plated material and a stainless steel nozzle, it is designed to be long-lasting and resistant to corrosion for years of use. Great for a modern touch in any home.
Chrome plated stout faucet with stainless steel nozzle.
Quickly and easily offer beer on tap with the Faucet Quick Disconnect (QD) Assembly. Made of chrome plated brass and stainless steel, this sturdy tapper Ball Lock Disconnect comes complete with all attachments for a compact and portable setup. No more expensive beer towers or messy beer lines. Craft the perfect sample of your home brew in seconds with this professional quality assembly.
This Duotight fitting makes it easy to split your gas line and run it to multiple kegs. Use one tee for a dual tap kegerator or two tees for a triple tap. You can also pair the tee with the Push-In Pressure Gauge to use the gauge with the BlowTie Spunding Valve. Compatible with EVABarrier 8 mm OD Tubing.
Duotight offers superior quality when compared to other push-in fittings. Their double EPDM O-ring design provides a more complete and reliable seal, protecting against leaks even when tubing is bent around tight corners. They are suitable for both beverage and gas applications, and are pressure rated to 100 psi. Tubing can be released by simply pushing in the collet and pulling the line out. No need for clamps or cutting lines!
Features:
Insert tubing and firmly push to connect
Easily release tubing by pushing in the collet
Suitable for both gas & beverage applications
Made from food-grade acetal plastic
Double O-rings made from highly chemical resistant EPDM
Locking teeth made from stainless steel
Pressure rated to 150 psi
Temperature rated to 212°F (100°C)
Please note: exposure to chlorine will degrade the acetal plastic and stainless steel these fittings are made from. Do not use in contact with bleach or other chlorinated cleaning chemicals.
The Blow Tie Spunding Valve is used to release excess pressure on a pressurized fermenter or from a keg while doing pressure transfers. Thanks to the large surface area of the diaphragm, this style spunding valve is much more accurate than the poppet style. 8 mm Duotight fittings at both inlet and outlet make this unit perfect for use with EVABarrier 8 mm OD tubing (D1717 or D1718). The blow off pressure can be set by either pairing the BlowTie with the Push-In Pressure Gauge (D1160), or by attaching it to an empty keg that has been pressurized to the desired psi.
Specifications:
Made from food grade acetal
Stainless screws
Easily disassembles for cleaning
8mm (5/16") Duotight fittings at both ends
0-40 psi pressure rating
Alkaline based draft line cleaner easily loosens soils and mineral deposits from beverage lines, faucets, and more. Works with all electrical, mechanical, and hand driven draft cleaning equipment.
BLC Beverage System Cleaner for direct draw systems, tap boxes, kegerators and home draft systemsEffective at only 1/2 oz per quart of waterUse on draft lines, coils, rods, faucets, fittings, parts and moreDissolves quickly in cold or warm waterNo hazardous shipping charges!
Instructions:
Add ½ oz BLC for each quart of water. Drain out beer and run solution into line. Circulate for 15 minutes, or longer if system is neglected. Flush cleaning solution from line and rinse with clean water. Re-tap and draw rinse water until beer appears.
This Black Washer/Gasket fits beer shanks and Sanke couplers, providing a reliable seal for your homebrew system. Crafted from a flat black material, this black beer washer ensures no leakage while also staying secure for long-term use.
The Brewmaster tap handle is designed to work with the full lineup of Brewmaster recipe kits. Each recipe sheet has a custom color cut out that can be slipped into the handle. The tap handle also includes multiple inserts with different writing surfaces, including reusable chalkboard and white board finishes.
Tap Board Features:
Designed to work with Brewmaster recipe kits
Includes removable inserts with different writing surfaces
Back of tap handle also serves as chalkboard surface
Dimensions: 7.25" H x 2.25" W x 0.75" D
This 4-Way Gas Distributor without PRV allows for uniform gas pressure to be dispensed from multiple kegs and is easily installed in any convenient location with the integrated wall-mount bracket. Gas manifolds create a draft dispensing system to quickly serve beer or other beverages, so you can ensure the perfect flavor every time.
Specifications
Perfect for dispensing up to four different beer kegs at the same output pressure.
These Valves are without check valve mechanism.
Made of Aluminum. Durable and light.
Stainless Steel 304 Wall Mounting Hardware Included.
5/16″ ID gas hose suitable for 3/8″ Barb.
Valves working and maintenance are easy because of tilted design.
Valve Material
Brass
Body Material
Aluminium
Outlet Connection
3/8" Barb (To fit 5/16" ID gas hose) C2121-100
Inlet Connection
3/8" Barb (To fit 5/16" ID gas hose) C2121-100
Performance
1 Pressure / 4 Keg
Type
Air Distributor
PRV - Pressure Release Valve
Not Included
Standard Packing
4
These premium brand new Kegland ball lock kegs are rated to 130psi working pressure and are made using a robotic orbital welding machine. The finish on these kegs are far superior to our other economy stainless steel kegs and are made with super smooth welds making them sanitary and easier to clean. The black rubber on these kegs also make them a little nicer to use around your house as they are less likely to damage your tile floors or crack plastic lining inside your kegerator.
These Premium 5 gal kegs have a lid with an internal tab/hook under the lid designed specifically for attaching dry hopping bags.
Features:
Ball lock
130 PSI Operating Pressure
5 Gallon (19 L) Capacity
Dry Hop Tab Welded into Lid
304 Stainless Steel
NSF Certified
Dimensions:
Height: 24.75 in.
Diameter: 8.375 in.
This 3-Way Gas Distributor without PRV allows you to dispense beer from multiple kegs with one gas source. Installed in a draft dispensing system, it maintains equal pressure from the regulator to all faucets and can split the gas delivery into several divisions. Connected to the primary regulator via a gas hose, it can also be wall-mounted for convenience.
Valve Material
Brass
Body Material
Aluminium
Inlet Connection
3/8" Barb (To fit 5/16" ID gas hose) C2121-50
Outlet Connection
3/8" Barb (To fit 5/16" ID gas hose) C2121-50
Performance
1 Pressure / 3 Keg
Type
Air Distributor
PRV - Pressure Release Valve
Not Included
Standard Packing
20
Connect just one cylinder to this gas distributor inlet and dispense from many beer kegs – all at the same time. You get the same pressure at all outlet points.
Available in 2, 3 and 4 way in Brass body. Krome’s gas line distributors come in with PRV and without PRV variants.
Stainless Steel 304 Wall Mounting Brackets and Screws Included.
3-way one barb end manifold – lets you serve from three kegs simultaneously
With PRV model
Brass material used for body.
Wall mount brackets included.
Individual shut off valve at each outlet
Beer shanks with coupling nut to attach faucet to one end, and beer thread (29/32 in 14 thread) nut and fittings to the other end. Chrome plated brass, 1/4 in bore. Typically used for mounting faucets through walls, refrigerators, cooler for jockey boxes, or other custom applications.
Double threaded back shank for jockey boxes. Features 29/32 - 14 thread Beer Thread on either end, and a 5/16 in ID bore through the center.This is a Chrome Plated Brass unit.
Dimensions:
3" - Shank Length
3" - Thread Length
1-7/8" - Pass Through Length
This 2.5 Gallon Ball Lock Corny Keg is of superior quality, with a 130psi working pressure, and orbital-welded craftsmanship. The stainless steel finish is extra smooth, providing a reliable, sanitary construction. The black rubber also ensures the keg won’t damage your home surfaces, making it perfect for use indoors.
These Premium 2.5 gal kegs have a lid with an internal tab/hook under the lid designed specifically for attaching dry hopping bags.
Features:
130 PSI Operating Pressure
2.5 Gallon (9.5 L) Capacity
Dry Hop Tab Welded into Lid
304 Stainless Steel
Dimensions:
Height: 14.5 in.
Diameter: 8.375 in.
This 2 Way Gas Distributor is the perfect solution for controlling the flow and pressure of gas in your system. Constructed without a pressure regulating valve, this gas distributor ensures that you have complete control over the pressure of your gas line. Enjoy safe, efficient, and reliable gas flow.
Stainless Steel 304 Wall Mounting Brackets and Screws Included.
2-way gas distributor – serve with ease from two kegs
Without PRV model
Made of Brass. Durable and reliable.
Wall mount brackets included.
Individual shut off valve at each outlet
Finish
Chrome Plated
Body Material
Brass
PRV - Pressure Release Valve
Not Included
Inlet Connection
3/8" Barb (To fit 5/16" ID gas hose)
Outlet Connection
3/8" Barb (To fit 5/16" ID gas hose)
Performance
1 Pressure / 2 Keg
Type
2 Way
Standard Packing
18
This 2-Way Gas Distributor with 60 PSI PRV is an excellent choice for transferring and distributing gas safely and reliably. The Pressure Relief Valve will protect your connected equipment from pressure spikes, while the 2-Way design allows you to easily monitor or control the flow.
Includes a Integrated check valve, so that gas can only flow in single direction, this can protect your regulator from accidental back up of beer.
Stainless Steel 304 Wall Mounting Brackets and Screws Included.
2-way gas distributor – serve with ease from two kegs
With PRV model
Made of Brass. Durable and reliable.
Wall mount brackets included.
Individual shut off valve at each outlet
Finish
Chrome Plated
Body Material
Brass
Outlet Connection
3/8" Barb (To fit 5/16" ID gas hose) C2121-50
Inlet Connection
3/8" Barb (To fit 5/16" ID gas hose) C2121-50
Type
Air Distributor
Performance
1 Pressure / 2 Keg
PRV - Pressure Release Valve
Included
Type
2 Way
Standard Packing
18
Our Two Piece Reusable Bung (Party Star Keg) is a reliable, airtight seal that preserves flavor, carbonation, and freshness. It fits securely and is easy to use. Craft beer lovers can keep their brews tasting as great as the day they were poured!
